Base and case
High-resistance polyamide based (PA) technopolymer.
Case in the following colours:
- C2: RAL 2004 orange, glossy finish.
- C3: RAL 7035 grey, glossy finish.
Available on request in RAL 7021 grey-black colour (C1).
Cover with perfectly sealed gasket and AISI 304 stainless steel UNI 6955 type self-tapping screws with six-lobe socket TORX® T06 (registered trademark by TEXTRON INC.).
The ultrasonic welding between the base and the case prevents separation and avoids dust and liquid penetration.
AISI 304 stainless steel with Ø 14 mm H7 reamed hole, fitting to shaft by means of AISI 304 stainless steel grub screw, hexagon socket and cup end UNI 5929-85, included in the supply.
Transparent polyamide based (PA-T) technopolymer, moulded over the case and with a perfect seal. Resistant to solvents, oils, greases and other chemical agents (avoid contact with alcohol during cleaning operations).
- 5-digit LCD of 8,0 mm height and special characters.
The visualization parameters can be set and modified by the operator by means of appropriate keys:
- values displayed in mm, inches or degrees
- display of mode for use (absolute or incremental mode)
- reading orientation (right or reverse).
Polyester membrane. Resistant to solvents, alcohol, acids, alkalis.
O-ring front sealing in NBR synthetic rubber assembled between the case and the boss.
Brass bushing with double O-ring sealing in NBR synthetic rubber inside the rear cavity of the base (DD51-E-SST-IP67).
Foam polyethylene, included in the supply.
Features and applications
DD51-E position indicators, with battery power supply, can be used on passing through shafts in any position to provide the reading of the absolute or incremental positioning of a machine component.
The 5-digit display of 8,0 mm height ensures excellent readability even from a distance and from different viewing angles.
The window in transparent technopolymer protects the LCD display against accidental shocks.
The high protection degree, IP 65 or IP67, makes the indicator suitable for applications that require frequent washing, even with intense water jets.
In the operating mode, by using the 3 function keys, it is possible to select the incremental or the absolute mode, the unit of measure (mm, inches or degrees), reset the absolute counter or load a preset source value and the preset offset value.
In the programming mode, through the 3 function keys, it is possible to program the reading after one revolution of the shaft, the direction of rotation, the display orientation, the resolution (number of decimal digits displayed), the source value and the offset value, the max. speed of rotation and set the functions of the keys among different options available.
The internal battery ensures long battery life (over 5 years). A special symbol appears on the display when it is necessary to replace the battery. The replacement can be performed easily by removing the front cover (Fig.1), without disassembly of the indicator from the control shaft and without the loss of configuration parameters.
Further technical information available in Operating instructions.
|Mechanical and electrical characteristics|
|Tension feed||Lithium battery CR2450 3.0 V|
|Battery life||5 years|
|Display||5-digit LCD of 8 mm height and special characters|
|Reading scale||-19999; 99999|
|Number of decimal digits||programmable (1)|
|Unit of measure|
mm. inches, degrees
|Rotation max. speed|
300/600/1000 r.p.m (2)
|Precision||10.000 impulses / revolution|
|Protection class||IP65 or IP67|
|Working temperature||0 ÷ 50 °C|
|Storing temperature||-20 ÷ +60 °C|
|Relative humidity||Max. 95% at 25°C without condensation|
|Interference protection||IEC 61326-1|
(1) See the operating instructions.
(2) Default: 600 r.p.m.
Higher rotation speed to 600 r.p.m. can be mantained for short periods of time.
The value of the max. speed affects the battery life.
Accessories on request (to be ordered separately)
- AISI 304 stainless steel RB51 reduction sleeves.
- Drill a Ø 6x10 mm hole in the body of the machine with a 22 mm centre distance from the shaft to fit the rear referring pin.
- Fit the indicator onto the shaft and make sure that the referring pin fit the hole.
- Clamp the bushing to the shaft by tightening the grub screw with hexagon socket and cup end, according to UNI 5929-85.
Scroll horizontaal onderaan de tabel en / of selecteer filters voor het gewenste resultaat