GN 581.5


__logo__INOX__ __logo__RoHS__ __logo__RUD__




Stainless Steel

  • German Material No. 1.4462
  • forged
  • 100 % electro magnetic tensile tested to EN 1677
  • blank


Stainless Steel

German Material No, 14462


Stainless Steel-Lifting eye bolts GN 581.5 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as potentially possible in Stainless Steel-Lifting eye bolts DIN 580 .

Stainless Steel-Lifting eye bolts GN 581.5 offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).

The rated load carrying capacity listed in the above table is clearly marked on the ring. It applies to the most unfavourable load application of the load types listed opposite.

Stainless Steel-Lifting eye bolts GN 581.5 eye bolts comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.

The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.

The hexagon socket bolt cannot be removed from the ring.

3Technical information
Method of mounting
Number11222223 and 43 and 43 and 4
Angles of inclination0°-7°90°0°-7°90°0° to 4545° to 60°asymm.0° to 45°45° to 60°asymm.
M 121.20 [0.34]0.50 t2.40 [0.68]1.00 t0.71 [0.24]0.50 t0.50 t1.06 t0.75 t0.50 t
M 162.40 [0.70]1.00 t4.80 [1.40]2.00 t1.40 [0.50]1.00 t1.00 t2.10 t1.50 t1.00 t
M 203.60 [1.20]2.00 t7.20 [2.40]4.00 t2.80 [0.86]2.00 t2.00 t4.25 t3.00 t2.00 t
M 245.20 [1.80}2.50 t10.40 [3.60]5.00 t3.50 [1.29]2.50 t2.50 t5.25 t3.75 t2.5 t
4Safety instructions

The loads given in brackets refer to the load capacity of the corresponding lifting eye bolt DIN 580. If such a value is not indicated the use of the lifting eye bolts DIN 580 is not permitted!

The bolt-on surface for the Stainless Steel-Lifting eye bolts GN 581.5 must be plane and at a right angle to the threaded borehole; the countersinking must be ≤ the nominal diameter of the thread.

Screwed in, the collar of the screw must make firm contact (do not use washers) and the eye bolt must rotate freely by 360°.

Before applying the load, turn the lifting eye bolt in the direction of the force. The lifting eye bolt is not suitable for frequent rotation cycles under load.

The specified load values apply for a minimum screw-in length of 1.5 × nominal thread diameter in Stainless Steel with a minimum tensile strength of 37 kp/mm2, at an ambient temperature of – 40° C to + 280° C. Load-bearing capacity under different conditions upon request.

Scroll horizontaal onderaan de tabel en / of selecteer filters voor het gewenste resultaat












Gewicht (g)

nominale belasting WLL




100355100 GN 581.5-M12
€ 134,07
12 30 M12 57 56 200 0.5 t [5 kN] M12 18 18
100355110 GN 581.5-M16
€ 161,76
14 36 n.v.t. 66 65 333 1.0 t [10 kN] M 16 24 22
100355120 GN 581.5-M20
€ 203,42
16 43 n.v.t. 77 74 520 2.0 t [20 kN] M 20 30 27.5
100355130 GN 581.5-M24
€ 279,52
19 51 n.v.t. 94 92 912 2.5 t [25 kN] M 24 35 33